FLC2000 Replacement Flat Screens: Compatibility, Specifications, and Selection Guide

FLC2000 replacement flat screens are shaker-screen panels intended for use on equipment identified as FLC2000, but the model name alone is not enough to confirm a fit. Before ordering, compare the screen’s overall dimensions, frame or hook-strip arrangement, support contact points, and required mesh specification with the screen currently in use and the shaker’s documentation. A suitable replacement must fit the deck securely and meet the solids-control requirements of the application. Yuanpeng can review your machine details and screen requirements to help assess compatibility before quotation.

View Details

Key Takeaways

• Confirm fit using the equipment identification and physical screen details, not the model name alone.
• Specify both separation requirements and construction details, including mesh opening, wire material, panel dimensions, and attachment style.
• Share photos, drawings, or a sample screen with your RFQ to reduce avoidable sourcing errors.
• Ask suppliers to state any assumptions, minimum order quantity, and estimated lead time in writing.

Who This Guide Is For

This guide is for drilling contractors, solids-control teams, maintenance departments, distributors, and procurement professionals sourcing FLC2000 replacement flat screens. It is useful whether you are replacing a damaged panel, standardizing spare parts, or comparing screen options for a specific fluid and operating condition. The recommendations are intended to support a purchasing decision, not replace the shaker manufacturer’s instructions. When the screen model or deck configuration is uncertain, verify it with the equipment supplier before installation.

What an FLC2000 Replacement Flat Screen Is

A flat screen is a replaceable screening panel installed on a shale shaker deck to separate solids from drilling fluid. Its performance depends on the combination of screen cloth, panel construction, shaker motion, fluid properties, and the way the screen is installed and supported. “FLC2000” identifies the equipment or screen family named in a buyer’s specification, but it should not be treated as a complete dimensional or performance specification. Different configurations, modifications, or previous replacements may affect the correct fit.

Screen Types, Materials, and Specifications

Mesh and Separation Requirements

Mesh count is one way to describe screen cloth, but mesh count alone does not define the opening or separation behavior. Wire diameter, weave, manufacturing tolerances, and the supplier’s method of describing the screen can also affect the resulting aperture. When possible, provide the required opening in micrometres (µm) alongside the mesh designation, and state whether you are matching an existing screen or targeting a particular solids-control outcome. Do not assume that two screens with the same mesh count will perform identically.

Wire Cloth and Panel Construction

Screen cloth may be made from different wire materials, and the choice should reflect the operating environment, fluid chemistry, abrasion exposure, and service expectations. Panel construction and attachment details matter just as much as the cloth: buyers should identify the frame or backing arrangement, edge treatment, and how the screen is retained on the deck. A screen that appears similar from above may not seat or seal correctly if its support geometry differs. Ask the supplier to confirm the construction against your machine details rather than relying only on a product name.

Information to Include in the Specification

A useful screen specification includes the equipment make and model, screen position if relevant, panel length and width in millimetres (mm), attachment style, mesh or aperture requirement, wire material preference, and order quantity in pieces. Include any drawing number or part number shown on the existing panel. If exact measurements are not available, provide clear photos of the screen, its edges, and its installed position, plus any available equipment documentation. These details give the supplier a basis for checking the request and identifying missing information.

Yuanpeng supply professional and honest service.

How to Match a Screen to Your Application

Start with the job the screen must perform rather than selecting by mesh label alone. Consider the solids you need to remove, the fluid being processed, expected flow conditions, and the operating priorities of the site, such as separation requirements or screen service life. There is usually a balance between finer screening and the risk of reduced fluid throughput or more frequent screen changes, but the actual result depends on operating conditions and screen design. Discuss the trade-off with your technical team and supplier instead of assuming that a finer screen is always better.

A Practical Compatibility Check

1. Identify the equipment: Record the shaker make, FLC2000 designation, serial or configuration details if available, and screen location.
2. Document the existing panel: Measure its length, width, and thickness in mm, and photograph the frame, edges, and retention features.
3. Confirm the screen specification: Record the mesh designation and, where available, the aperture in µm and wire material.
4. Check the deck interface: Compare the attachment method and support contact points with the installed screen and equipment documentation.
5. Request written confirmation: Ask the supplier to identify the basis for compatibility and flag any dimensions or assumptions that still need verification.

As a format example only—not an FLC2000 standard or recommended screen specification—a buyer might describe a sample requirement as “panel envelope: 1,000 mm × 600 mm; target opening: 100 µm; quantity: 10 pieces.” These figures illustrate how units can be stated in an RFQ; they are not a fitment recommendation. Replace them with verified dimensions and process requirements for your equipment.

Pricing, Minimum Order Quantity, and Lead Time

Screen pricing can depend on panel construction, wire material, mesh specification, order quantity, and whether the request requires custom confirmation or production. Minimum order quantities and lead times vary by supplier, specification, and current production schedule, so they should be confirmed for each quotation. When comparing offers, check whether the quoted product includes the same dimensions, attachment configuration, and mesh description. A lower unit price is not a useful comparison if the quoted screens do not meet the same fit and application requirements.

Supplier Evaluation Checklist

Choose a supplier that asks for the information needed to verify the screen rather than confirming fit from the model name alone. Review whether the quotation clearly describes the proposed dimensions, cloth specification, materials, quantity, and any unresolved assumptions. Ask how the supplier handles drawing review, sample comparison, packaging, and order updates, and request available product documentation relevant to your procurement process. Do not treat broad statements such as “fits all FLC2000 shakers” as a substitute for configuration-specific confirmation.

Common Selection Mistakes

• Ordering by model name only: Equipment configurations and replacement histories can differ; verify the physical interface.
• Using mesh count as the only criterion: Confirm aperture, wire details, and the application requirement where possible.
• Ignoring panel dimensions: A screen that is close in size may not seat securely or make the intended deck contact.
• Changing specifications without review: A different opening or construction can change screening behavior, so assess it against site requirements.
• Leaving commercial terms unclear: Confirm quantity, MOQ, packaging, and estimated lead time before placing the order.

Work with Yuanpeng on Your Screen Requirement

For an FLC2000 replacement flat screen inquiry, send Yuanpeng the equipment identification, screen dimensions, mesh or aperture requirement, wire material preference, quantity, and delivery destination. Photos, drawings, or a sample-screen description can help clarify the attachment and support details. Yuanpeng can review the information, identify questions that need confirmation, and provide a quotation based on the agreed specification. If you are unsure which details are critical, share what you have and request a compatibility review before ordering.

Conclusion

The right FLC2000 replacement flat screen is the one that matches both the shaker’s physical interface and the separation needs of your operation. Confirm dimensions and attachment details, specify mesh and material requirements, and obtain written clarification on compatibility, MOQ, and lead time. Your next step is to compile the existing screen or equipment details and send them with your quantity requirement to Yuanpeng for review and quotation.