1.5 Inch Stainless Welded Mesh Panel: Specifications and Buying Guide

A 1.5 inch stainless welded mesh panel is a rigid grid made by joining stainless steel wires at their intersections, with a nominal mesh opening of 1.5 inches—equivalent to 38.1 mm. To buy the right panel, confirm how the opening is measured, then specify wire diameter, stainless steel grade, panel dimensions, edge finish, and required quantity. These details affect fit, strength, corrosion suitability, fabrication, and the final quotation. Because suppliers may interpret mesh spacing differently, put the measurement method and tolerances in your inquiry.

Please visit our website for more information on this topic.

Who This Guide Is For

This guide is for procurement teams, fabricators, contractors, and equipment manufacturers comparing stainless welded mesh panels for a project or production run. It is useful when you know you need a 1.5 inch opening but have not finalized the wire, material grade, panel size, or finish. It can also help you prepare a clearer RFQ and compare supplier responses on an equivalent basis. Always verify project-specific requirements with your engineer or end user before ordering.

Understanding the 1.5 Inch Mesh Specification

The mesh opening describes the space between wires, but the quoted dimension may refer to the clear opening or to the distance from the center of one wire to the center of the next. Those measurements are not interchangeable: wire diameter affects the clear space when pitch is specified center-to-center. Ask the supplier to state which method is used on the drawing or quotation. This prevents a nominally correct panel from arriving with openings that do not match your assembly or screening requirement.

What Welded Construction Means

In welded wire mesh, perpendicular wires are joined at their intersections to form a grid. The panel format can make handling and installation more convenient than working with a roll, depending on the panel size and application. Weld quality, wire diameter, and panel flatness should be considered alongside the opening dimension. Request the relevant product details rather than assuming that all panels with the same mesh size have the same load capacity or finish.

Key Specifications to Include in an RFQ

A useful specification gives the supplier enough information to identify the required product and flag any unresolved choices. If you are still evaluating options, mark flexible items as “to be advised” and ask for alternatives rather than leaving them unstated. The following table provides a practical checklist for a quotation request. Project drawings, operating conditions, and applicable regulations should take precedence where they apply.

Choosing a Wire Diameter and Stainless Grade

There is no single wire diameter that is right for every 1.5 inch panel. A lighter wire may suit a different purpose than a panel expected to resist handling loads or serve as a structural component, so do not select diameter from mesh opening alone. For early comparison, you can ask a supplier to quote alternatives such as 3 mm and 4 mm wire, clearly treating them as options rather than universal standards. Confirm the finished dimensions and suitability with the responsible project professional.

Stainless steel grade should be selected according to exposure, cleaning requirements, temperature, and any chemical contact. Buyers often compare commonly specified grades such as 304 and 316, but the suitable choice depends on actual operating conditions and relevant project rules. Do not treat “stainless steel” as a complete material specification. State the grade you require, and ask what material identification or documentation the supplier can provide for the order.

Shunqiang Wire Mesh Product Page

Match the Panel to the Application

A 1.5 inch grid may be considered for partitions, guards, racks, equipment enclosures, or other assemblies where the opening and panel format suit the design. These are potential use categories, not a guarantee that a particular panel meets a required safety, load, or regulatory standard. Confirm whether the panel is intended to screen, separate, protect, support, or provide ventilation, since these functions can require different wire sizes and construction details. If people, machinery, or elevated loads are involved, obtain an appropriate engineering review.

Check Fit, Handling, and Installation

Provide the final panel width and length, not only the mesh opening. If the panel will be cut, framed, bent, or attached to another structure, tell the supplier how the edges will be used and whether cut edges need additional preparation. Consider access routes and handling equipment when selecting panel dimensions, especially for larger orders. Where the panel must fit an existing frame, share the frame dimensions and clarify whether measurements are internal, external, or nominal.

A Practical Selection Framework

1. Define the job. Describe what the panel must do and the environment where it will operate.
2. Confirm the opening. State 1.5 inch (38.1 mm) and whether this is clear opening or center-to-center spacing.
3. Set the material details. Specify the stainless grade and wire diameter, or request clearly identified alternatives.
4. Provide dimensions and quantity. Include panel width, length, tolerances, number of panels, and any cutting or fabrication needs.
5. Align quality and delivery requirements. List inspection documents, packing, destination, and required delivery window.
6. Review the quotation. Check that the quoted specification matches your RFQ and ask suppliers to identify exclusions or substitutions.

Pricing, MOQ, and Lead Time

Panel pricing can vary with stainless grade, wire diameter, panel size, order quantity, edge treatment, packing, and shipping destination. Minimum order quantity and lead time also depend on the supplier’s production schedule, material availability, and the level of customization. We recommend requesting a quotation against a complete specification rather than comparing a unit price without its assumptions. Ask suppliers to separate product cost, any processing charges, packing, and freight where applicable.

For a fair comparison, make sure each quotation uses the same opening definition, material grade, wire diameter, dimensions, tolerances, and quantity. Confirm whether the lead time begins after order confirmation, drawing approval, or another agreed milestone. If your schedule is fixed, state the required delivery date early and ask the supplier to confirm feasibility in writing. Avoid treating an indicative estimate as a confirmed production or shipping commitment.

Supplier Evaluation Checklist

• Does the supplier confirm whether 1.5 inch refers to clear opening or center-to-center pitch?
• Are grade, wire diameter, panel dimensions, and tolerances explicitly stated?
• Can the supplier clarify available edge finishing, packing, and inspection documentation?
• Does the quotation identify MOQ, lead-time assumptions, and any exclusions?
• Will the supplier review a drawing or sample specification before production?

At Shunqiang Wire Mesh, we work with buyers to clarify welded mesh panel requirements and prepare quotations based on the requested specification. Share your drawing or RFQ, including the opening definition, grade, wire diameter, panel dimensions, quantity, and destination. If some details are not fixed, identify them as open questions so we can discuss feasible options for your project. Final availability, tolerances, documentation, price, and schedule should be confirmed for the specific order.

Summary and Next Steps

The key to buying a 1.5 inch stainless welded mesh panel is to define more than the opening size. State that the opening is 1.5 inch (38.1 mm), clarify how it is measured, and confirm the wire diameter, stainless grade, panel dimensions, finish, quantity, and delivery requirements. These details help suppliers quote comparable products and give your team a sound basis for technical review. Before ordering, approve the final specification or drawing and confirm all commercial terms with the supplier.

To request a quotation from Shunqiang Wire Mesh, send your project requirements and any available drawing. We can review the specification with you, identify information that may need clarification, and discuss options for the intended application. A complete RFQ is the most practical next step toward accurate product evaluation and sourcing.